Pace sidetalk 1000b mods install#

(IN = L10, OUT = L11/C59.)Įuropean-made version of Uniden 'clone' chassis above (same circuit, different part numbers)Įuro 3900: Remove C64. NOTE: If in doubt about your specific chassis, check the other AM/FM “clone” listings below or send us the exact chassis details.Ĭherokee CBS2100, NR100, NR150, Connex 3300, 3500, Dirland 3300, 3500, 3600, 3700, 3900, Eagle 2000, Excalibur (base), Excalibur Samurai, Galaxy 11B, Galaxy 2100, Galaxy II, Galaxy DX33, DX44, DX55, DX66, DX73V, DX77, DX88, DX99, Galaxy Jupiter, Galaxy Melaka, Galaxy Pluto, Galaxy Saturn, Galaxy Sirius, General Lee, Mirage 44, Mirage 6600, Mirage 88, Mirage 9900, Mirage II, Mirage III, Northstar 3000, 4000, 6000, 9000, 9500, President Franklin, Super Galaxy, Superstar Grant, Superstar 3300, 3500, 3600, 3900: Remove C58. Uniden “clone” multimode copycat models using MC145106 PLL and with EPT3600-10A, -10Z, -11A, 11Z, -13B, -14B or similar Ranger-type chassis. Uniden Multimode Export w/MC145106 PLL, PC999 chassis Stalker 9-FDX, President McKinley export: Remove C57. Uniden Multimode Export w/MC145106 PLL, PC893 chassis Uniden Multimode Export w/MC145106 PLL, PC879 chassisĬobra 148GTL-DX (early): Remove C48. Uniden 'clone' Multimode Export w/MC145106 PLL, EPT00JA-10Z chassis Uniden Multimode Export w/MC145106 PLL, PB042 chassis Uniden Multimode Export w/MC145106 PLL, PB010 chassisĬobra 148GTL-DX (late), President Richard, Superstar 360FM: Ham Int’l Concorde III, Jumbo III, Multimode III. Remove wire from “I.” (IN = wire from T12, OUT = “I.” (C120/D14 junction next to T13.)Ĭybernet PLL02A Export, PTBM125A4X or PTBM131A4XĬolt 1600DX, 2000DX, HyGain 8795 (V), Lafayette 1800, Midlannd 7001 export, Pacific 160, Superstar 2000, Tristar 777: Remove C120.

Pace sidetalk 1000b mods install#

Cut this wire and install the CG in series.Ĭybernet PLL02A Export, PTBM121D4X, PTBM121COXĬobra GTL150, Colt 320DX, 320FM, 1200DX (Excalibur), Ham Int’l Concorde II, HyGain 2795DX, Intek 1200FM, Lafayette HB70AFS,Tristar 747: A wire marked “H” runs from one secondary terminal of T12 (the terminal not going to C116/R90) to the pad marked “I” next to T13 (that contains one end of C120/D14). Ham Int’l Concorde, Jumbo, Multimode II, HyGain V, Lafayette 1200FM, Major M360, M588: A wire marked “C” runs from the secondary terminal of T10 not going to C111/R88, to a foil pad containing one end of C122 and D12 on the main PTBM059 board, near T13. 3-5875A Superbase, Midland 78-574, 78-999, SBE LCBS-4: Remove C279 on RF board.Ĭybernet PLL02A Export, PTBM059COX & PTOS006 or PTSY016AOX Install CG in series.Ĭybernet PLL02A American, PTBM080/085COX & PTRF004/005DOX Cut this wire and install the CG in series.ĭak Mark X only: Cut gray shielded cable connecting T10/C121 to CFl/D12. Pearce-Simpson Super Panther, RCA 14T302, Truetone CYJ4837A-87, Universe 5600:Ī wire marked “C” runs from the secondary terminal of T10 not going to C111/R88, to a foil pad containing one end of C122 and D12, near T13. Yes, the Channel Guard Filters will help with Channel Bleedover Interference.ġ0.695 MHz AM/SSB HOOKUP LIST BY PLL CHASSIS TYPEĬybernet PLL02A American & Canadian, PTBM048AOX or PTDM058COXĪWA/Thorn 1503, Boman CB950, Cardon Iroquois 40, Colt 480, 485DX, 890, 1000, 1200 (Excalibur), Gemtronics GTX77, G.E. There are a few stations in this area that are to darn loud and bleed all over me.

Also try to ADD the filter to the exsisting one now you have 2 filters not one.

In some radios if you don't the blanker will not work. PLEASE PLACE ALL OF YOUR CHANNEL GUARD INSTALLATON QUESTIONS HERE. Closed: New threads not accepted on this page